It is not possible in DipTrace now. However some users recommended the following utility to get large crosshair:
http://www.mlin.net/CrossHair.shtml
Search found 3131 matches
- 06 Jul 2010, 07:44
- Forum: DipTrace PCB Layout
- Topic: Large Crosshairs
- Replies: 2
- Views: 5235
- 25 Jun 2010, 05:30
- Forum: DipTrace Schematic Capture
- Topic: Nets not connected between pages
- Replies: 8
- Views: 10130
Re: Nets not connected between pages
Make sure that netports have the same type.
Wires on different sheets are joined to single net if they connected to same type of netports.
Wires on different sheets are joined to single net if they connected to same type of netports.
- 21 Jun 2010, 03:59
- Forum: Feature requests
- Topic: 3D and Breadboard Views
- Replies: 11
- Views: 15491
Re: 3D and Breadboard Views
Next version will be released when we do all features that we plan to add. There is not exact date when it will happen.
- 21 Jun 2010, 03:52
- Forum: DipTrace PCB Layout
- Topic: 5 vdc Reg. Heat Sink Area
- Replies: 4
- Views: 7836
Re: 5 vdc Reg. Heat Sink Area
If you want to open additional area from solder mask (more than pads area), you can do it in following way: Select Top Mask or Bottom mask (depending on where heatsink is) from drop-down box on drawing panel. Then choose shape type (filled rectangle, ellipse or polygon) and define its points on desi...
- 21 Jun 2010, 03:42
- Forum: DipTrace News and Events
- Topic: Diptrace Video Tour Audio
- Replies: 3
- Views: 11377
Re: Diptrace Video Tour Audio
Currently, DipTrace video tour is without sound.
- 18 Jun 2010, 05:22
- Forum: Bug reports
- Topic: tl431acz pinout mismatch
- Replies: 1
- Views: 5308
Re: tl431acz pinout mismatch
I see the problem. Thank you. It will be fixed in next version.
- 18 Jun 2010, 03:22
- Forum: DipTrace PCB Layout
- Topic: How do I switch to different footprint?
- Replies: 1
- Views: 4925
Re: How do I switch to different footprint?
If you design board without schematic, right click in PCB Layout on any pattern you want to change and select "replace pattern" in submenu. Then choose new pattern and change "Apply to" option to "Similar type patterns". If you design project with schematic, you should replace patterns for all compo...
- 17 Jun 2010, 09:33
- Forum: DipTrace PCB Layout
- Topic: How can I set how many layers I want to use ?
- Replies: 1
- Views: 4955
Re: How can I set how many layers I want to use ?
For manual routing, just route wires on single layer. For shape auto-router, open auto-router setup, go to settings tab, click on "Use priority layer direction" option. Then turn-off Top or Bottom layer. For grid auto-router, open auto-router setup, unselect option "use all layers" and set number of...
- 17 Jun 2010, 09:02
- Forum: Feature requests
- Topic: 3D and Breadboard Views
- Replies: 11
- Views: 15491
Re: 3D and Breadboard Views
3D view feature is currently in progress. It will be added in next version.
- 16 Jun 2010, 02:27
- Forum: DipTrace PCB Layout
- Topic: Busses in Schematic not showing in PCB
- Replies: 7
- Views: 9331
Re: Busses in Schematic not showing in PCB
So, if I want to keep analog and digital power as separate nets, then I should not connect them to the actual power in the schematic. I should connect them only when routing the PCB. Is that right? If you want to keep analog and digital grounds as separate nets, you can connect them via 0 Ohm resis...